LED-NEON-FLEX

LED-NEON-Flex  
Color available: Blue, White, Yellow and Red.
Though neon has long been the mainstream of the outdoors linear lighting, it is also known for its technical weaknesses, including complicated installation, fragile glass nature, potential shock hazard, high maintenance cost and high power consumption. However, the market for outdoor linear lighting is so vast that many manufactures try to find a perfect substitute for neon, but they all fail to solve the above problems. With over 2 years  advanced LED technologicalresearch and development work, the producer has finally succeededin producing LED-NEON-Flex to replace glass neon. Compared with glass neon, it is easier to cut and can be bent into what ever angles by hand, installation can be within minutes and most important it gives no hot spot on appearance.

 

 

Installing Mode:

The LED-NEON -FLEX is a versatile and user-friendly lighting device; it can be cut and bent and formed in the field and easily installed on the flat surface of varied materials, such as wood, plastic, steel, or wall, etc. to form all kinds of pattern according to your design. And it can be easily connected to the power supply and then performs well.

  • It is recommended to mark centerlines or draw the outline of your pattern on the surface of your desired positions.
  • Secure mounting clips on the centerlines at appropriate intervals with screws, if there are curves; It is better to secure mounting clip on each curve and between.
  • Insert the light body into the mounting clips with the lighting parts upward.
  • Connect each part together.
  • [Warning:]

    When using outdoor use portable lighting products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit or outlet to be used for LN-FX only having built-in GFCI protection receptacles can be used.

 
Cutting mark

LN-FX Must be cut only on the indicated mark

 Linear installation

channel LN-FX-CH

 Curve installation

1. Mini channel LN-FX-5
2. Screw
 90° Installation
1. Mini channel LN-FX-5
2. Screw		 180° Installation

Includes:
1. Mini channel LN-FX-5
2. Screw

 

 Convex installation

Mini channel LN-FX-5

 
 
Concave installation

Includes:
Mini channel LN-FX-5

  Installation with the slot

Press LN-FX into the slot of the installation

  
 Easy Connector
Front Connector includes:
1. Female power connector LN-FX-CA-1
2. MALE CONNECTING PIN ln-fx-ca-2
3. Heat shrink tube		 Sliceable Connector includes:
1. Male connecting pin LN-FX-CA-3
2. Heat shrink tube		 Attachable End Cap: LN-FX-CA-4
Front connector
1. Molded power connector LN-FX-M-1		 Molded end cap: LN-FX-M-2 High Voltage Power Supply
1. Power plug
2. AC/DC Converter
 X Connector

Includes:
1. X connector LN-FX-CA-2
2. Male connector pin LN-FX-CA-2
3. Heat shrink tube

 

 T Connector

Includes:
1. T connector LN-FX-T
2. Male connector pin LN-FX-CA-2
3. Heat shrink tub

 L Connector

Includes:
1. L connector LN-FX-1
2. Male connector pin LN-FX-CA-2
3. Heat shrink tube
   
Middle connector with cable

Includes:
1. Female power connector LN-FX-CA-1
2. Male connector pin LN-FX-CA-2
3. Heat shrink tube

 

    

 
  • Read And Follow All Safety Instructions.
  • LN-FX must be cut only on the indicated mark.
  • Before connecting with connectors, bending LN-FX rightwards and leftwards, Extra copper wires need to be cut with nippers.
  • Ensure LN-FX and power source have the same voltage.
  • Pay more attention on the polarity, when connecting two pieces.
  • Do not use if there is any damage on LN-FX or cord insulation, Inspect periodically.
  • Do not submerge LN-FX in liquids, or use the product near any water source.
  • Do not secure this product or its cord with staples, nails, or like means that may damage the insulation.
  • Do not subject LN-FX to continuous flexing.
  • If the paint on the light body is damaged, please use adhesive tapes or fabrics with reflective and fireproof property to cover the lower part of the light body to prevent light leakage

E-Mail  

Fax -Nr. 0049 341 3582431

Tel.-Nr. 0049 341 3582420

Homepage


  • Read And Follow All Safety Instructions.
  • LN-FX must be cut only on the indicated mark.
  • Before connecting with connectors, bending LN-FX rightwards and leftwards, Extra copper wires need to be cut with nippers.
  • Ensure LN-FX and power source have the same voltage.
  • Pay more attention on the polarity, when connecting two pieces.
  • Do not use if there is any damage on LN-FX or cord insulation, Inspect periodically.
  • Do not submerge LN-FX in liquids, or use the product near any water source.
  • Do not secure this product or its cord with staples, nails, or like means that may damage the insulation.
  • Do not subject LN-FX to continuous flexing.
  • If the paint on the light body is damaged, please use adhesive tapes or fabrics with reflective and fireproof property to cover the lower part of the light body to prevent light leakage